Showing results: 106 - 120 of 293 items found.
-
165 CB -
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
FC-2 -
Shenzhen Chuangxin Instruments Co., Ltd.
This Flushing Test device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005,etc. Accordance with requirements of IPX5/6.Applied to carry out waterprooftest on LED lamps, house hold appliances, electric and electronic products and other electric accessories.
-
MBT-MIL -
ZTS Inc
The ZTS MBT-MIL Multi-Battery Tester (MBT-MIL) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
MBT-1 -
ZTS Inc
The ZTS Multi-Battery Tester (MBT-1) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Lisun Electronics Inc.
The standard test temperature is 25, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
Lasermet Ltd.
Lasermet is the UK’s leading test house for testing to the following standards:EN 60825-1 / IEC 60825-1*EN 60825-2 / IEC 60825-2EN 60825-12 / IEC 60825-12*EN 60601-2-22 / IEC 60601-2-22*21 CFR 1040.10and is the only test house with UKAS accreditation for laser and LED testing (other than the National Physical Laboratories).
-
TBM300 -
Telonic Berkeley, Inc.
The Model TBM300 Portable Opacity Meter consists of two basic units connected by a single cable. The sensor unit is installed end-of-line on the exhaust outlet of the vehicle under test and contains the light source (green led) and receiver (photo detector) modules.
-
Lisun Electronics Inc.
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
6201 IN (Ranges: 5kV, 10kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● High quality Taut Band movement.● Two insulation test voltages.● Insulation resistance, auto ranging on all ranges.● Low Battery LED indication.● Beeper warning of external voltage.● Fully protected : crow bar.● Housed in carry case.
-
1943 -
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
AD-710 -
ADEX Urzadzenia Pomiarowe
4 Connectors measurement method, Readable LED indicator 12,7 mm high with brightness control, Autoranging, Slow turning on and off test current (measurement of high inductance elements). Memorisation of 25 results of measurement. Power Supply: High-efficiency acidic ? gel battery
-
Shanghai MCP Corp
Taut-Band movement.26 measuring range with Min. 1mV and 100uA(MS506-A) both in AC and DC.Zero at midpoint function (voltage meter,current meter and galvanometer 3 in 1).Overload warning LED indicator.Input impedance:100kΩ at all voltage ranges.Battery test function
-
NeonPro
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
1966A -
Peaceful Thriving Enterprise Co Ltd
*Check voltage on 70-440V AC.*With CE, cUL and RoHS Approval.*Operates by two LR44 1.5V batteries.*LED will glow if AC voltage is present.*Check for proper ground connection of electrical appliance.*Test electrical lines, cables, sockets, fuses, switches and etc.
-
Haug
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.